Flickering lights aren’t ghosts. They’re faults. If the lights in your office, warehouse, or workshop flicker, buzz, or drop out after hours, or an emergency light stays dark during its test, something in the electrical installation needs attention. This guide is for facilities managers, business owners, and anyone responsible for a commercial building. It explains the most common causes of flickering lights in commercial buildings, which warning signs mean you should call an electrician promptly, and why a failed emergency lighting test matters more once the clocks go back and people are leaving work in the dark.
Why lights flicker, buzz, and fail
Most flickering has an ordinary explanation. The trick is working out which one, because the same symptom can come from a tired lamp or from a connection that’s slowly overheating inside a wall.
Ageing fluorescent tubes and control gear
Older fluorescent fittings rely on control gear (a ballast, and in many fittings a starter) to strike and run the tube. As tubes and starters near the end of their life, they flicker, glow at the ends, or take several attempts to come on. Older magnetic ballasts can also hum or buzz, and that noise is easier to notice in a quiet building after everyone has gone home.
Loose or overheating connections
A loose terminal in a fitting, switch, or junction box can make a light flicker as the connection makes and breaks. This is the cause to take most seriously. A poor connection creates heat, and heat damages insulation over time. Discoloured accessories, a faint burning smell, or a switch plate that feels warm are all signs to stop using the circuit and get it checked.
Overloaded or shared circuits
Lights that dip when a large piece of equipment starts up often point to circuits that are heavily loaded or poorly balanced across the distribution board. After-hours work can make it worse, with cleaning equipment, heaters, and chargers all plugged in at once. The fix might be as simple as moving loads, or it might mean new circuits.
LED drivers and dimmer mismatches
LED lighting is far less prone to flicker than fluorescent, but only when the driver and any dimming controls are compatible. A retrofit lamp in an old fitting, or an LED panel on a dimmer it wasn’t designed for, can produce a visible flicker or a strobing effect that people find tiring.
Problems on the supply
When lights flicker across several circuits or the whole building at once, the cause may be further upstream: in the distribution board, the main incoming connections, or the supply itself. That needs testing by an electrician, and occasionally involvement from the network operator.
Warning signs that shouldn’t wait
Not every flicker is urgent, but some symptoms point to a risk of overheating, shock, or fire. Call an electrician promptly if you notice:
- A burning or hot plastic smell near fittings, switches, or the distribution board.
- Scorch marks or discolouration on sockets, switches, or light fittings.
- Buzzing or crackling from the distribution board itself.
- Breakers or RCDs (residual current devices) that trip repeatedly.
- Flickering that affects several circuits at once.
- Lights that dim noticeably whenever equipment starts.
Please don’t open fittings or the board to investigate. This guide is for awareness only and isn’t installation guidance. All electrical work must be carried out by competent persons to BS 7671 and UK regulations.
The emergency light that fails its test
Emergency lighting is the part of the system nobody notices until the mains fails. Then it has to light escape routes, exits, and key equipment so people can get out safely.
Government fire safety guidance for offices and shops notes that emergency escape lighting is likely to be needed where premises are used during darkness, including the early darkness of winter days. It also recommends a monthly test of emergency lighting, an annual test and maintenance visit by a competent person, and a logbook of all maintenance and testing. On 31 October, just after the clocks go back, the light outside fades a little after 5pm, so the timing matters.
Why emergency lights fail
The most common reasons a fitting stays dark, or fades early during a test, are:
- Batteries that have reached the end of their life and no longer hold charge.
- A failed lamp or LED module.
- A fault in the charging circuit, so the battery never fully recharges.
- Wiring or connection faults, sometimes left behind by later alterations.
- Fittings that have been switched off at a local isolator and forgotten.
A single failed fitting can often be repaired or replaced. When failures keep appearing across a site, replacing the system usually makes more sense than chasing faults one at a time. At Fayrefield House in Crewe, Ranger Electrical Services (North West) Ltd carried out a full emergency lighting replacement, installing 20 new emergency bulkheads with new conduit, a complete wiring upgrade, and local isolation on each fitting, which reduced the existing failures.
The standard has changed
The British Standards Institution published a new edition of the emergency lighting code of practice, BS 5266-1:2025, on 31 October 2025, replacing the 2016 edition. It now covers local area lighting and standby lighting as well as emergency escape lighting. If your system was designed some years ago, it’s a sensible moment to ask whether it still matches how the building is used today.
How an electrician tracks down the cause
Good fault finding starts with questions rather than tools. When does the flicker happen? Is it one fitting, one room, or the whole floor? Does it coincide with machinery starting, or with the heating coming on? Those answers narrow the search before a single cover comes off.
From there, an electrician will typically inspect the affected fittings and accessories, test the circuits involved, and check the distribution board for loose connections and signs of heat. Thermal imaging of distribution boards can reveal a hot connection long before it causes a failure. Once the cause is clear, the remedy might be new control gear, a replacement fitting, rebalanced circuits, or rewiring where the cabling has reached the end of its useful life. Ranger’s general electrical services cover repairs and maintenance, safety inspection and testing, lighting, rewiring, and reactive maintenance for commercial, industrial, and large residential sites.
Repeated faults are a sign that the installation needs a proper look. An Electrical Installation Condition Report (EICR) assesses the condition of the whole fixed installation and codes anything that needs action. Our EICR guide for commercial properties explains what it covers and how to prepare a site.
There’s no single interval that suits every building. HSE guidance says electrical installations should be tested often enough that there is little chance of deterioration leading to danger.
Keeping it fixed
Planned maintenance is cheaper and less disruptive than reacting to failures. Scheduled testing, a tidy logbook, and early repairs keep small faults from turning into a dark corridor or a closed site. Our article on preventing downtime with commercial electrical maintenance sets out how a maintenance programme fits around a working business.
If your fittings are old fluorescent units, a fault visit is also a good time to consider an LED lighting upgrade. Replacing failing fittings with compatible LED fittings and drivers removes the most common sources of flicker and buzz in one go.
Questions about flickering lights at work
Is a flickering light dangerous?
Sometimes. A tube at the end of its life is a nuisance rather than a hazard. Flickering caused by a loose or overheating connection can damage insulation and create a fire risk, so if you can’t tell which it is, get it checked.
Why do the lights flicker only at night or after hours?
Often it’s simply that the building is quieter and darker, so you notice it more. It can also be a real pattern: cleaning equipment, heaters, or chargers running after hours can load circuits differently from the working day.
Will switching to LED stop the flickering?
It removes the flicker caused by ageing tubes and control gear. It won’t fix a loose connection, an overloaded circuit, or a supply problem, so the cause should be found before new fittings go in.
How often should emergency lighting be tested?
Government fire safety guidance recommends a monthly test, an annual test and maintenance by a competent person, and keeping a logbook of the results. Your fire risk assessment may set out more for your premises.
Who is responsible for emergency lighting in a commercial building?
Under fire safety law, the responsible person is usually the employer, owner, landlord, or whoever controls the premises. They must put in place and maintain appropriate fire safety measures, which include emergency lighting where it’s needed.
What should we do if an emergency light fails its test?
Record the failure in the logbook, arrange a repair, and think about whether that area is safe to use after dark in the meantime. Your fire risk assessment should guide any temporary measures.
Does an EICR include emergency lighting?
An EICR looks at the fixed electrical installation. Emergency lighting has its own testing routine, but the two visits can often be combined so one site visit covers both.
Halloween is the one night of the year when a flickering light is part of the fun. For the rest of the year, it’s a message from your installation that something needs a look. Find the cause, fix it properly, and keep the emergency lighting tested, and the only ghosts in the building will be the ones in the decorations.
Have a project or question about compliance-first electrical or renewable installs?
๐ 01606 212 775 | โ sales@rangerelectricalservices.co.uk
๐ https://rangerelectricalservices.co.uk/contact/